The thickness of a thermal corrective render is not fixed: it is sized project by project, according to the local thermal requirement aimed for, the condition of the substrate and the available thickness constraint. The relation R = e / λ shows that thermal resistance grows with the applied thickness. Compared with a dedicated insulant, a corrective render is nonetheless installed in low thickness: it is a tool for correction and continuity, not a thick insulant.
The thermal resistance of a layer is calculated from two quantities only: its thickness and its thermal conductivity (λ). The relation is direct: R = e / λ, where e is the thickness in metres, λ the conductivity in W/(m·K) and R the resistance in m²·K/W.
Two lessons follow. First, at constant conductivity, doubling the thickness doubles the resistance of the layer: thickness is indeed a direct lever of performance. Second, at constant thickness, the lower the conductivity of the material, the higher the resistance — this is what the lightweight fillers of a corrective render aim for. The resistance of a complete wall then adds up those of each layer and the surface resistances, and it is this sum that determines the U-value of the assembly.
A practical consequence: because the λ of a mortar remains higher than that of a dedicated insulant, reaching a given resistance requires more thickness with a render than with an insulation panel. This is the structural reason why a corrective render is not sized like an insulant, and why its thickness is a compromise rather than a maximum value.
No "standard" thickness applies to every project. The chosen thickness results from a trade-off between several constraints, the main ones being below.
| Factor | Effect on the thickness to adopt |
|---|---|
| Local thermal requirement (target R / U) | The more ambitious the resistance or comfort objective, the more thickness is needed, at a given conductivity. |
| Condition and nature of the substrate | A sound, regular wall accepts a uniform application; a degraded or heterogeneous substrate requires making good and conditions the applicable thickness. |
| Available thickness (renovation) | Roof overhangs, window reveals, party walls and alignments often limit the space: the physical constraint takes priority over the thermal ideal. |
| Planned finish | The finish adds its own thickness and requires a regular keying surface, which counts in the total applied. |
| Flatness and workmanship tolerances | Making up flatness defects consumes thickness; a controlled application limits unnecessary over-thickness. |
In renovation, the available thickness constraint is frequently the deciding factor: this is precisely where a render applied in a thin layer, without panels or framing, keeps its interest when a thick added insulation is not feasible.
The relation R = e / λ is linear for the layer alone, but the effect felt at the scale of the wall is not. What matters for comfort and heat loss is the overall U-value, which varies as the inverse of the total resistance. Yet adding resistance to a wall that already has some produces a less and less visible gain: going from a low to a medium resistance changes a lot, going from medium to high changes less.
In concrete terms, the first millimetres of a corrective render clearly raise the internal surface temperature and soften the "cold wall" effect; beyond that, each additional centimetre brings a real but increasingly modest gain, for an extra material and labour cost that stays proportional. There is therefore a relevant thickness range, beyond which piling on material is no longer economically justified.
A corrective render is a mortar: its conductivity, even lowered by lightweight fillers, remains higher than that of a dedicated insulant. For that reason, aiming for the same resistance as a thick insulant would require unrealistic mortar thicknesses on a facade — weight, stability, overhangs, cost. The product therefore finds its field of use in low thickness, where it excels: envelope continuity, absence of cold joints, treatment of singular points and improvement of surface comfort.
This positioning is not a flaw but a definition: a corrective render plays on thermal correction and perceived comfort, not on the pursuit of an absolute minimum U, which is the role of a dedicated insulant sized for it.
There is no universal thickness that would be "the right one". Any stated thickness only makes sense in relation to a specific thermal objective, substrate and space constraint. The relevant thickness is therefore determined through study, by combining the local requirement, the condition of the wall, the available space and the planned finish — and not by copying a value read elsewhere.
The system distributed by Isoltech Green is built on the thermo-active render Pro-Tech®: a 100% natural render, applied continuously with no adhesive or fixings, paired with the Techdekor Green finish. Isoltech Green is its European importer and developer (not its manufacturer). In practice, the applied thickness starts at 10 mm, typically in the 10 to 20 mm range, and the system can be built up to 100 mm where a project calls for it; it is defined project by project according to the substrate and the correction target. We do not publish any λ/R/U figure attributed to Pro-Tech® outside an identifiable report. The 40 to 60% gains mentioned by our customers are customer feedback, not a guaranteed performance. Technical details on Pro-Tech®.
This page complements the Thermal corrective render dossier and the Building thermal correction guide. For the underlying physics, see thermal resistance, thermal conductivity (λ) and U-value.