Page · thermal quantity

Inside surface temperature: cold walls, condensation and comfort

What is the inside surface temperature?

The inside surface temperature, written Tsi, is the temperature of a wall's inside face (wall, ceiling, glazing), expressed in °C. It depends on the wall's U-value and on the ambient conditions: the more insulating the wall, the closer its surface stays to the indoor air temperature. A surface that is too cold creates a cold-wall sensation and, if it drops below the dew point, a risk of condensation and mould.

What the surface temperature depends on

The inside surface temperature is not a fixed property of the wall: it results from the balance between the heat crossing the wall and the exchanges at its surface. It depends on:

  • the U-value of the wall (its overall heat loss);
  • the indoor air temperature (Ti) and the outdoor air temperature (Te);
  • the inside surface resistance Rsi, which describes the exchange (convection + radiation) between the indoor air and the surface.

The more insulating the wall (low U), the closer the inside surface stays to the air temperature. A highly lossy wall, on the contrary, lets its surface cool: it is the "cold wall" felt when approaching it, which degrades the perceived operative temperature.

Dew point and condensation

The dew point is the temperature at which the air, once cooled, reaches saturation (100% relative humidity) and begins to condense its water vapour. If a wall's surface temperature drops below the dew point of the ambient air, water deposits on that surface: this is surface condensation.

This phenomenon is the classic starting point for mould, which can develop even before visible condensation, as soon as the relative humidity at the surface stays durably high. The most exposed zones are corners, window reveals and thermal bridges, colder than the rest of the wall.

The temperature factor fRsi (ISO 13788)

To judge the risk of condensation and mould at a cold spot, the surface temperature factor fRsi is used, defined by the ISO 13788 standard:

fRsi = (Tsi − Te) / (Ti − Te)

where Tsi is the inside surface temperature, Ti the indoor air temperature and Te the outdoor air temperature. The result is a dimensionless number between 0 and 1.

  • An fRsi close to 1 means the surface stays almost as warm as the indoor air: the wall is well insulated at that point.
  • A low fRsi signals a cold spot (often a thermal bridge) where the surface falls towards the outside: an increased risk of condensation and mould.

The criterion is to check that the calculated fRsi stays above a required minimum value, itself deduced from the ambient conditions and climate to prevent the surface from reaching critical humidity. Singular points (corners, junctions) are calculated in a two-dimensional regime under ISO 10211.

Example of a qualitative reading

Consider a room at Ti = 20 °C and an outside at Te = 0 °C. On a well-insulated main part of the wall, the surface may stay around 18–19 °C: the fRsi is high, well above the usual thresholds. In a poorly treated corner, the same wall may see its surface fall to a few degrees above the outside: the fRsi drops, and this is precisely where mould appears first.

These values are illustrative: the real surface temperature is calculated from the wall's characteristics (calculation/simulation) or read on site (measurement). The two approaches are complementary and must not be confused.

How is the surface temperature measured?

Two families of approach coexist, which must be clearly distinguished:

ApproachTool / methodUse
On-site measurementContact surface thermometerPoint reading of a surface
On-site measurementThermal camera — infrared thermography (EN 13187)Mapping of cold spots and thermal bridges
Condensation diagnosisSurface probe + ambient hygrometerCompare Tsi with the calculated dew point
Calculation / simulationThermal model (ISO 13788, ISO 10211)Predict fRsi and risk before works

Infrared thermography, framed by EN 13187 for the detection of thermal irregularities in the envelope, visualises the cold zones directly. Pairing a surface probe with hygrometry lets you compare the surface temperature with the current dew point.

Limits of interpretation

  • The surface temperature depends strongly on the instantaneous conditions (indoor and outdoor temperature, humidity, sunshine, heating): a measurement is a snapshot of a moment, not a constant.
  • Corners and thermal bridges are the critical points: a wall that is correct in its main part can condense locally.
  • The surface temperature is an indicator of comfort and risk, to be cross-checked with the U-value and hygrometry; it does not replace the full calculation of the wall.

Go further

This page complements the Thermal correction of facades guide.

Call — +351 927 917 736