Guide · critical junction

Balcony

Why is the balcony the most pronounced thermal bridge?

A cantilevered balcony is the direct extension of the floor slab towards the outside: the same concrete crosses the facade and the insulation. It acts as a cooling fin, exposed to the outdoor air on both faces and over its whole surface, which efficiently draws heat away from the indoor floor. This is why its linear coefficient ψ is often the highest on the facade, well above that of a simple slab edge. Its effects are high heat loss and an internal cold point at the junction, prone to condensation and mould.

The fin effect

A traditional balcony is not merely a break in the insulation: it is a genuine heat-exchange surface. The slab that projects from the facade plane offers the outside cold a large surface (top, soffit, edge) thermally connected to the heated floor. In building physics, this is called the fin effect or cooling fin, by analogy with heat sinks. It is what distinguishes the balcony from the simple slab edge, where the slab stops at the face of the facade: the balcony extends and amplifies the bridge.

How is it quantified?

The bridge is characterised by a linear coefficient ψ (W/m·K) applied to the length of the balcony-facade junction.

Heat loss of the balcony:  Hψ = ψ · Ljunction  (ψ in W/(m·K), L support length of the balcony)

The value is determined by the default values of EN ISO 14683 or, more finely, by a detailed ISO 10211 calculation — all the more useful here, since the three-dimensional geometry of the balcony (corners, balustrades) often moves the real value away from the tabulated figures.

ConfigurationIndicative ψ (W/m·K)Severity
Untreated cantilevered balcony (continuous slab)≈ 0.50 – 1.00Very high
Balcony with thermal break≈ 0.20 – 0.40Reduced
Structurally separated / add-on balcony on insulated supports≈ 0.10 – 0.25Controlled
Generic orders of magnitude drawn from published building physics. The 3D geometry of the balcony makes the ISO 10211 calculation particularly recommended. These benchmarks do not replace a project calculation.

Consequences

The balcony sharply lowers the internal surface temperature along the junction, at the ceiling of the lower storey and at the base of the wall of the upper storey. It is a frequent point of condensation and mould in dwellings with continuous balconies. In energy terms, the repetition of balconies on a facade can weigh heavily in the heat-loss balance, depending on local regulations.

How is a balcony's thermal bridge treated?

The balcony is the most difficult critical junction to treat, because a cantilevered slab cannot simply be "wrapped" the way a flat facade can. Strategies combine according to the context:

  • In new build: integrate a thermal break (a structural insulating element, under a European Technical Assessment, ETA) at the junction, which strongly reduces the ψ while carrying the loads.
  • In renovation: insulate the balcony on its accessible faces (top, soffit, edge) to limit the fin effect, or, in severe cases, remove the balcony and replace it with a structurally separate add-on structure on insulated supports.
  • Treat the continuity of the facade around the balcony with external wall insulation, a continuously applied render limiting residual junctions.

None of these solutions "removes" the bridge of an existing balcony entirely: they reduce it, and the result must be verified by calculation or by thermography. Where the balcony can be neither thermally broken nor structurally separated, it must be accepted and documented in the balance.

Limits of interpretation

  • The 3D geometry of the balcony makes default values particularly approximate: prefer an ISO 10211 calculation.
  • Insulating the faces of an existing balcony reduces the fin effect but does not cut the structural path through the slab.
  • Load-bearing requires that any thermal break or structural separation be studied by a structural engineer.
  • Depending on the building, a conventional EWI or IWI with local treatment may remain the best-suited solution.

This guide complements the Thermal correction of buildings dossier and the Thermal bridges cluster. Isoltech Green is a European distributor; the choice of a solution falls to a project study.

Call — +351 927 917 736