Guide · critical junction

Roof & parapet

Why is the wall-roof junction a thermal bridge?

The junction between the facade wall and the roof brings together two distinct insulation layers — that of the walls and that of the covering — which struggle to meet. On a flat roof, the parapet (the masonry upstand around the perimeter) extends the wall above the roof and forms a fin exposed to the cold on three faces. These junctions create a linear thermal bridge at the top of the building, with heat loss and a cold point at the ceiling corner, where condensation and mould appear first. It is quantified by a linear coefficient ψ (W/m·K), which depends on the continuity between the wall insulation and the roof insulation.

Flat roof and pitched roof

Two families of configurations concentrate the thermal bridge at the top of the building:

  • Flat roof with parapet: the parapet is a perimeter upstand wall in concrete or masonry, projecting above the waterproofing. Exposed to the cold on its external face, its top and its internal face, it acts as a fin (the same mechanism as the balcony) and is one of the most delicate bridges on flat roofs.
  • Pitched roof: the bridge lies at the junction between the insulation of the sloping planes and that of the walls, notably at the wall plate, the eaves overhang and the feet of the roof structure.

How is it quantified?

The bridge is characterised by a linear coefficient ψ applied to the length of the wall-roof or parapet junction.

Heat loss of the top junction:  Hψ = ψ · Ljunction  (ψ in W/(m·K))

The value is determined by the default values of EN ISO 14683 or, better, by a detailed ISO 10211 calculation, recommended for the parapet, whose geometry departs from the tabulated cases. The risk of condensation at the ceiling corner is assessed by the temperature factor fRsi (EN ISO 13788).

ConfigurationIndicative ψ (W/m·K)Sensitivity
Wall/roof insulation continuity ensured≈ 0.05 – 0.20Low
Parapet insulated on its faces≈ 0.20 – 0.50Moderate
Untreated parapet (bare concrete upstand)≈ 0.50 – 0.90High
Generic orders of magnitude drawn from published building physics. The real ψ depends on the parapet geometry and the continuity of the insulation layers; it is calculated to EN ISO 14683 or ISO 10211. These benchmarks do not replace a project calculation.

Consequences

The top-junction bridge lowers the internal surface temperature at the ceiling-wall connection, often visible as dark traces around the perimeter of the ceiling of the top storey. It increases roof heat loss, already a major item in the thermal balance since heat rises. Untreated, the parapet can also encourage waterproofing defects linked to temperature differences.

How are these thermal bridges treated?

The principle remains the continuity of the insulation between the facade and the roof:

  • Carry the facade insulation up to meet the roof insulation, wrapping the parapet from the outside where possible.
  • Insulate the parapet on its faces (external, top, internal) to break the fin effect, in coordination with the waterproofing.
  • Ensure the overlap of the wall/roof insulation without interruption, carefully treating the connection with the vapour control layer and the air barrier.

An external wall insulation that rises up to the parapet, a continuously applied render, makes this overlap easier. Here too, the bridge is not "removed": it is reduced and the result is verified by calculation or by thermography. The thermal treatment must always be coordinated with the roof waterproofing.

Limits of interpretation

  • Treating the parapet is inseparable from the waterproofing: any intervention must preserve the upstands and the continuity of the waterproofing system.
  • The default values of EN ISO 14683 are conservative; an ISO 10211 calculation is recommended for the parapet.
  • The height and geometry of the parapet sometimes limit the insulation thickness that can be added to it.
  • Depending on the building, a conventional EWI or IWI with treatment of the top junction may remain the best-suited solution.

This guide complements the Thermal correction of buildings dossier and the Thermal bridges cluster. Isoltech Green is a European distributor; the choice of a solution falls to a project study.

Call — +351 927 917 736