Because tiles have a higher thermal effusivity than wood. Effusivity, written b, measures the speed at which a surface exchanges heat on contact. A high-effusivity surface (tiles, metal) quickly absorbs heat from the hand and feels cold; a low-effusivity surface (wood, cork) absorbs it slowly and feels warm, even though both are at the same temperature.
Thermal effusivity characterises a material's ability to exchange heat with whatever touches it, in the transient regime (just at the moment of contact). It governs the sensation felt on touch, distinct from overall heat loss.
Its unit is the J·m⁻²·K⁻¹·s⁻¹ᐟ², also written J/(m²·K·√s) or equivalently W·√s/(m²·K). The higher b, the faster the surface "pumps" heat from the body that touches it, hence the colder it feels to a hand warmer than itself.
Effusivity is calculated from three properties of the material: its thermal conductivity λ, its density ρ and its specific heat capacity c:
b = √(λ · ρ · c) (λ in W/(m·K), ρ in kg/m³, c in J/(kg·K))So a material that is dense, able to store a lot of heat (high c) and a good conductor will have high effusivity. Conversely, a light, poorly conductive material, such as wood or an insulant, will have low effusivity and feel "warm".
These values illustrate the ranking of material families; they are orders of magnitude, not project values:
| Material | Effusivity (relative order of magnitude) | Contact sensation |
|---|---|---|
| Cork, light insulants | Very low | Warm |
| Wood | Low | Rather warm |
| Plaster, brick | Medium | Neutral to cool |
| Concrete, stone, tiles | High | Cold |
| Metals | Very high | Very cold |
Effusivity explains the touch comfort of a floor or a wall: at the same temperature, a wooden floor is perceived as more pleasant than a tiled one, because it draws heat from the foot more slowly. It is also what distinguishes the "cold wall" sensation from the real surface temperature: a wall can be at a good temperature yet feel cool on contact if its effusivity is high.
This quantity belongs to the transient contact regime — the instant two bodies touch — not to pure conduction or steady-state heat loss.
In practice, effusivity guides the choice of coverings in direct contact with the body: living-room and bedroom floors, worktops, seats. A low-effusivity covering (wood, cork, textiles) is perceived as warmer, while a high-effusivity surface (tiles, stone, polished concrete) feels cool, which may be sought in a warm climate. This perception is independent of the insulation level of the supporting wall: you can have a thermally well-insulated floor whose covering feels cold, and vice versa.
When two bodies of different temperatures touch, the temperature that settles at the interface does not sit halfway: it is weighted by the respective effusivities. The body with the higher effusivity "imposes" its temperature on the contact zone more strongly.
T_contact ≈ (b₁·T₁ + b₂·T₂) / (b₁ + b₂)This is why a hand placed on cold metal feels almost the metal's temperature: the metal's high effusivity dominates, and the skin cools quickly at that spot. On wood at the same temperature, the interface stays much closer to the skin's temperature, hence the warm sensation.
Effusivity and diffusivity are sometimes confused, two transient quantities that are nonetheless different. Thermal diffusivity (α = λ / (ρ·c)) describes the speed of propagation of a heat front inside the material, while effusivity describes its ability to exchange heat at the surface at the moment of contact. The same set of properties (λ, ρ, c) feeds both, but they answer distinct questions: "how fast heat advances in the mass" (diffusivity) versus "how fast the surface draws or releases heat" (effusivity).
Effusivity is determined in the laboratory by transient methods, which observe the thermal response of the material just after a brief heat input: the hot wire, hot plate or transient plane source methods. These techniques measure the temperature rise and the flow simultaneously, from which effusivity (and often conductivity and diffusivity) is deduced.
This page complements the Thermal correction of facades guide.