Short, sourced answers to the most frequent questions on thermal correction, panel-free facade insulation, building physics, old buildings, moisture and measuring the gains. Each answer links, where one exists, to its detailed article.
This page gathers fifty practical questions on thermal correction and the facade, grouped by theme: basic concepts, physical quantities, panel-free insulation, old buildings, moisture, measuring the gains and the Isoltech Green system. The answers are deliberately brief and grounded in public standards; the linked articles go deeper into each subject.
Thermal correction means the set of actions that improve the real thermal behaviour of an existing wall: raising the temperature of its inner face, removing the cold-wall effect, limiting thermal bridges. Broader than insulation alone, it targets perceived comfort by working on conduction, radiation and thermal mass, and not only on the R-value.
Learn more →Insulation, in the regulatory sense, adds thermal resistance to reach a quantified heat-loss target (target U), in steady state. Thermal correction is broader: it improves the real behaviour of the wall (surface temperature, cold wall, thermal bridges, summer comfort). A correction can include insulation, but also covers effects that R alone does not describe.
Learn more →Not always. It improves comfort and the behaviour of the wall and can be enough in light renovation. But to reach a very low U-value required by regulations, a dedicated high-resistance insulation is often still needed. The right choice depends on the objective, the substrate and the building's constraints; it is decided after a survey.
Learn more →Yes, especially from the outside. By keeping the wall's mass on the heated side, you preserve the thermal mass and time lag, which delay the entry of summer heat and smooth the temperatures. This is a major asset of solid buildings, which internal insulation tends to neutralise. Summer comfort also depends on solar shading and night ventilation.
Learn more →A corrective render is a mortar applied in a continuous layer to improve a wall's thermal behaviour, without panels or frame. Its value is continuity (no cold joints), low thickness and the ability to follow an irregular substrate, which makes it suited to old buildings and to treating junctions.
Learn more →A thermo-active render acts on thermal behaviour through several mechanisms beyond the conduction described by R: radiation, time lag, dynamic behaviour. It therefore targets real in-use comfort, hard to sum up in a single laboratory value, while being applied as a continuous envelope without panels.
Learn more →A corrective render shines on old buildings, facades with relief, low thicknesses and refurbishment-plus-comfort projects, because it is continuous and thin. It is an alternative to EWI, especially where EWI cannot be installed. For a quantified regulatory requirement on a flat facade with no thickness constraint, a certified EWI system remains the reference. The choice is always decided after analysing the building.
Learn more →Yes. An external correction in a continuous envelope treats the thermal behaviour and renews the appearance of the facade in a single operation. It is one of the major advantages of the approach: you refurbish and gain in thermal comfort at the same time, while limiting thermal bridges, with no significant added thickness when the render is thin.
Learn more →Thermal conductivity λ (W/(m·K)) measures a material's ability to conduct heat. The lower λ, the more insulating the material. It rises sharply when the material is damp, which is why a wet wall insulates far less well than a dry one. It is an intrinsic property of the material, independent of thickness.
Learn more →Thermal resistance R (m²·K/W) measures a layer's ability to oppose the passage of heat for a given thickness: R = e/λ. The higher R, the more insulating the layer. The resistance of a complete wall is the sum of the resistances of its layers and of the surface exchange resistances.
Learn more →The U-value (W/(m²·K)) is the heat flux crossing 1 m² of wall for 1 °C difference between the two environments. The lower U, the better the wall performs. It is the inverse of the sum of the wall's thermal resistances, including the surface resistances. It is the regulatory reference quantity.
Learn more →R characterises a layer or set of layers: the higher, the better. U characterises the complete wall and its inverse is the sum of the resistances: the lower, the better. In short, R rises with performance, U falls. You add the R-values of the layers, then U = 1 divided by the sum of the resistances.
Learn more →A thermal bridge is a localised zone of the envelope where heat escapes faster than on the main wall: slab edges, partitions, window sills, corners, junctions. It creates cold spots on the inner surface, so risks of condensation and mould, and can represent a notable share of the heat losses of an insulated building.
Learn more →Thermal mass is a wall's ability to store heat and smooth out indoor temperature variations. Strong thermal mass stabilises the indoor climate and improves summer comfort, a major asset of old stone buildings. It depends on the mass, the specific heat capacity and the position of the mass in the wall.
Learn more →The thermal phase shift, or time lag, is the time, in hours, a peak of outdoor heat takes to cross a wall and reach the inside. A good time lag, of the order of 8 to 12 hours, shifts the afternoon heat towards the night, when you can ventilate. It is accompanied by a damping of the amplitude and improves summer comfort.
Learn more →Effusivity b = square root of (λ·ρ·c) measures the speed at which a surface exchanges heat on contact. It explains why tiling feels colder than wood at the same temperature: it draws heat from the skin faster. It is a quantity of perception, distinct from thermal resistance.
Learn more →Operative temperature is the temperature actually felt: a weighted average of the air temperature and the mean temperature of the walls around us (radiation). That is why raising the surface temperature of a wall improves comfort at equal air temperature. It explains the feeling of cold near a poorly insulated wall.
Learn more →Facing a cold wall, the body loses heat by radiation towards that surface, even if the room air is at 20 °C. You then feel the cold. Raising the temperature of the wall's inner face, through thermal correction, removes this effect and also reduces the risk of condensation in the corners.
Learn more →The dew point is the temperature at which air, as it cools, reaches saturation and its water vapour begins to condense. When a surface drops below this point, water deposits on it. It is the reference for assessing the risk of surface condensation and mould on a wall.
Learn more →Breathability is a wall's ability to let water vapour diffuse through it, to "breathe". On old buildings it is essential: a too-sealed system traps moisture and damages the wall. You favour layers increasingly open to vapour towards the outside, so as not to block drying.
Learn more →Yes. A correction by continuous render applies a thermo-active mortar directly onto the wall, without panels, adhesive or through fixings. This approach ensures a continuous envelope with no cold joints, in low thickness, particularly suited to old buildings and facades with relief. Performance depends on the substrate, the thickness applied and the workmanship.
Learn more →A panel-free correction offers perfect continuity (no joints or panel thermal bridges), low thickness, no through fixings and good adaptation to irregular substrates and junctions. It keeps the wall's thermal mass and lets you refurbish and correct the thermal behaviour in one operation. Its resistance per centimetre stays lower than a thick dedicated insulant.
Learn more →The phrase "zero thermal bridge" refers to an envelope applied in one continuous piece, without joints or fixings, which extends the insulation into the junctions (reveals, parapets, slab edges) where panels leave cold zones. Continuity limits the interruptions, but the real result always depends on the care taken in workmanship around the junctions.
Learn more →No, unlike internal insulation. Placed on the facade side, external insulation does not reduce the living area and keeps the wall's thermal mass on the heated side. It adds an external thickness, moderate with a thin render, and changes the appearance of the facade, which assumes that it can be altered.
Learn more →From the outside as soon as the facade can be altered: you keep the wall's thermal mass, treat thermal bridges continuously and renew the appearance. Internal insulation stays useful in a protected area, in blocked shared ownership or room by room, but reduces thermal mass and space and complicates the treatment of thermal bridges.
Learn more →A thin corrective render improves the thermal behaviour and the perceived surface, but its resistance per centimetre is lower than that of a dedicated low-λ insulant. Its value is continuity, low thickness and the treatment of old buildings, not maximum resistance. For a very low U, you need more thickness or a dedicated insulant.
Learn more →A continuous render follows mouldings, relief and junctions, where rigid panels adapt poorly. It is an asset on buildings with worked facades. On the other hand, where decorative relief must stay legible and uncovered, no external coating — thermo-active or not — is suitable, and you turn to the inside.
Learn more →A certified panel EWI remains the reference for a quantified regulatory requirement, on flat, regular facades of large area, or where a funding application requires a high rated R for the insulation system, easier to justify with a product that has a documented R. When thickness is not constrained, it reaches maximum resistance more efficiently.
Learn more →By respecting its ability to manage moisture: you favour vapour-open materials over sealed barriers, and you correct from the outside when the facade can be altered, to keep the wall's thermal mass. You first treat any rising damp, then raise the thermal resistance. A watertight system on the wrong side traps water.
Learn more →By taking into account the vapour permeability of fired clay, which absorbs and releases moisture: you keep this breathing with vapour-open materials. You correct preferably from the outside to keep the thermal mass and treat thermal bridges, after checking the moisture state, the adhesion of the renders and the sensitivity to frost.
Learn more →You treat it as a breathing whole: thick walls bedded in lime, without a capillary break. You keep the vapour permeability, treat moisture and ventilation first, then correct the thermal behaviour, often starting with the loft and the joinery. On the walls, external is preferable if the facade can be altered.
Learn more →Often, conventional external insulation is prohibited or discouraged on the street facade, as it would drown the mouldings. The preferred route is then a breathable internal correction, sometimes a thermo-corrective render in low thickness on a non-moulded facade, and the treatment of accessible thermal bridges. Any intervention requires the agreement of the authorities and of the shared owners.
Learn more →You do not fit insulation on a historic structure: you improve comfort while respecting conservation. The large solid walls have considerable thermal mass; any intervention must stay reversible, breathable and approved by the authorities. You act mainly on suitable heating, ventilation, the loft, and occasionally breathable renders on undecorated walls.
Learn more →Old walls regulate moisture by absorbing and releasing it. Placing a sealed material in the wrong place blocks evaporation, makes water stagnate, causes salt efflorescence, frost damage, delamination and degrades the masonry. The golden rule for old buildings is to keep the wall breathing, with layers increasingly open to vapour towards the outside.
Learn more →Yes, imperatively. A damp wall insulates poorly, because water increases its conductivity, and it decays. Rising damp, infiltration and lack of ventilation must be diagnosed and treated beforehand. Insulating a wet wall hides the problem, traps moisture and accelerates the damage. Diagnosing water always precedes thermal correction.
Learn more →Rising damp is the rise of ground water in a wall by capillarity, through its fine pores, common in old buildings without a capillary break. It carries salts that crystallise at the surface (efflorescence) and is recognised by a horizontal moisture tide mark at the base of the wall. It is treated before insulating.
Learn more →Condensation shows up as misting and black mould in corners, behind furniture or on cold spots. It appears when damp indoor air meets a surface colder than its dew point. It is linked to thermal bridges, the cold wall and insufficient ventilation, to be distinguished from rising damp and infiltration.
Learn more →Yes, markedly. Water, a far better conductor than the air trapped in the pores, strongly increases the material's thermal conductivity and makes the wall's resistance collapse. A water-logged wall can lose a significant part of its insulating power. That is why treating moisture is an essential precondition for any thermal correction.
Learn more →By distinguishing four levels: laboratory measurement (λ, R, U of a product), on-site measurement (in-situ behaviour), simulation (regulatory or dynamic calculation) and customer feedback (perception and bills). On site, you compare a reference state before works, an in-situ U measurement and a monitoring of climate-corrected consumption, under comparable conditions.
Learn more →No. A thermal camera reveals surface temperature differences and locates thermal bridges and defects: it is an excellent qualitative diagnostic, framed by the EN 13187 standard. But a thermal image is not a quantified performance value: that is measured (in-situ heat flow meter) or calculated under defined conditions. The two approaches are complementary.
Learn more →It is the measurement of the U-value of a real wall, on site, by the heat flow meter method framed by the ISO 9869 standard: a heat-flux sensor and temperature probes record over several days to smooth the variations. It gives the real behaviour, distinct from laboratory values and simulations.
Learn more →No. R, and the U that follows from it, describes the heat loss in steady state, but comfort also depends on the radiation of the walls, thermal mass, time lag and surface uniformity. Two walls of the same U can give a different feel. Judging a wall on R alone leads to incomplete conclusions, especially in summer.
Learn more →Not always. Thickness increases thermal resistance, but beyond a certain point the marginal gain diminishes, and the added thickness may be impossible in renovation (roof overhangs, sills, party walls). The issue is to reach the objective within the building's real constraint, taking into account thermal mass and moisture management too.
Learn more →A corrective render can be applied on most masonry substrates: concrete, stone, brick, masonry and sound adherent old renders, provided the substrate is sound and the adhesion good. Its ability to follow relief makes it suited to old buildings. The wall's moisture state and vapour compatibility must be checked beforehand, project by project.
Learn more →Yes. As soon as a home's air-tightness is improved, controlled ventilation (MVHR or a system suited to the fabric) becomes essential to remove water vapour and indoor pollutants. Without it, moisture builds up and condensation, and therefore mould, reappear. Ventilation and insulation go together, particularly on old buildings.
Learn more →Isoltech Green distributes across Europe a panel-free facade thermal-correction system: the Pro-Tech thermo-active render, applied in a continuous layer without adhesive or fixings, paired with the Techdekor Green finish. The system corrects the wall, treats the junctions and renews the facade in one operation, particularly suited to old buildings and low available thicknesses. It is an alternative to EWI, especially where EWI cannot be installed.
Learn more →Pro-Tech is a mineral thermo-active render applied as a continuous envelope, without panels or adhesive, at the heart of the Isoltech Green system. It acts on the wall's thermal behaviour continuously, without joints or panel thermal bridges, and adapts to irregular substrates. Its performance is sized project by project according to the climatic zone and local requirement.
Learn more →The gains reported by our customers are in the order of 40 to 60% savings. These are customer feedback, to be distinguished from a laboratory measurement, a simulation or an on-site measurement. The real result depends on the state of the building, the thickness applied, the substrate and the whole set of works (roof, joinery, ventilation).
Learn more →For transparency, we do not publish any λ, R or U figure attributed to Pro-Tech outside an identifiable report. As the material is thermo-active and heterogeneous, its real behaviour (radiation, time lag, fire, acoustics) does not reduce to a laboratory R, which underestimates it. The thickness is sized to meet the local requirement, project by project, and always starts at 10 mm.
Learn more →Isoltech Green is developing a network of applicator and distributor partners across Europe. Every project starts with an analysis of the facade according to good practice. To join the network or study a project, contact us: we support the sizing, the workmanship and the skills development of our partners on the system.
Learn more →Continuous render correction or conventional EWI, old or recent building: the right system is decided after a survey. Our teams will get back to you.